Tankless water heater, no hot water
A gas smell, a carbon monoxide alarm, a leak or a burning smell means act now. Otherwise read the error code, check power and the water valves, and call a pro for repeat codes, ignition or anything gas.

On this page
A tankless unit heats water as it flows, so when the hot water stops there is no tank of reserve to fall back on. Most tankless units burn gas, and they also need electricity for their controls, so the cause can be a supply problem, a safety shutdown or a part that has failed. This tool sorts those apart and keeps the dangerous cases at the front.
Tankless water heater, no hot water
Gas and carbon monoxide first, then the power, water and error code checks an owner can make. Gas parts and repeat error codes are for a licensed pro.
Do you smell gas, or has a carbon monoxide alarm sounded?
I smell gas
Act now
Leave now and call for help
A gas smell near a gas water heater can mean a leak. Do not check the gas valve or the unit yourself.
What to do
- Leave the home now with everyone in it, and keep pets with you if you can do that quickly.
- Do not turn lights or appliances on or off, use a lighter or match, or try to find the leak.
- From outside, call 911 and your gas utility's emergency number.
- Stay out until the utility or the fire department says it is safe.
A CO alarm sounded or someone feels sick
Act now
Get into fresh air and call emergency services now
Fuel-burning appliances can release carbon monoxide if they are not venting properly.
What to do
- Get everyone, including pets, into fresh air now. Open the door on your way out.
- Call 911 from outside. Symptoms can look like the flu: headache, dizziness, weakness, nausea or confusion.
- Do not go back in to switch the appliance off. Wait for the fire department or a gas utility technician to say it is safe.
- Have the appliance inspected by a qualified technician before it runs again.
Neither
Is water leaking from the unit or its pipes, or is there a burning smell?
Yes
Act now
Turn it off and call a licensed professional now
Leaks and burning smells are safety problems, and the manufacturer lists water leaks among the reasons to call a professional.
What to do
- If there is smoke or fire, leave and call 911.
- Stay out of standing water and do not touch wet electrical equipment or the panel.
- Call a licensed plumber or heating professional now. Do not open the unit.
No
Does the unit show an error code on its display?
Write the code down before you do anything else.
Yes, there is a code
Did you look the code up in the manual and do the reset it describes, and does the code come back?
Not yet
Deal with it soon
Look up the code and try the manual's reset once
Codes point to ignition, venting, flame or water flow problems. The manual says which reset applies to your model.
What to do
- Find the code in the owner's manual and do only the reset it describes.
- If the code returns, stop and call a qualified technician.
- Do not open the unit or work on gas parts.
Yes, it came back or the unit keeps shutting down
Deal with it soon
Call a qualified technician
A code that persists after a reset, or repeated shutdowns, are on the manufacturer's list of reasons to call a professional. Ignition failures and gas supply concerns are not homeowner jobs.
What to do
- Tell the technician the error code and what you already tried.
- Do not relight anything or touch gas connections.
- If you smell gas at any time, go back to the top of this tree: leave and call for help.
No code, or the display is dark
Does the unit have power, with its breaker on, and are the water shutoff valves to it open?
Check the panel only if you can reach it safely and dry. Leave gas valves alone.
Breaker tripped, and I switched it off and on once
Did the breaker trip again, or does the unit still show nothing?
It tripped again
Act now
Stop resetting it and call a licensed professional now
A breaker that trips again means a fault in the unit or its circuit.
What to do
- If you see smoke or flames, or the smell is strong, leave the home and call 911.
- Otherwise switch the equipment off at the thermostat and leave any breaker that tripped off. Do not keep resetting it.
- Call a licensed HVAC professional or electrician now. Do not open panels or touch wiring.
No, it is back on
Keep an eye on it
Watch it for a day
A tripped breaker is one of the listed reasons a tankless unit has no hot water. If it holds, the cause may have been a one-off.
What to do
- Run hot water at one fixture and see whether it heats.
- Check the temperature setting. DOE recommends 120 degrees F for water heaters. A lower setting also lowers scalding risk.
- If the breaker trips again, leave it off and call a licensed electrician or plumber.
Yes, power and water are fine
Is the problem hot and cold swings, or weak flow, rather than no heat at all?
Yes, it swings or the flow is weak
Keep an eye on it
Check the setting and filters, then ask about descaling
Mineral scale, clogged inlet filters, a wrong temperature setting or several fixtures running at once can cause swings.
What to do
- Check the temperature setting and run fewer hot water fixtures at the same time.
- Ask a plumber or the manufacturer how to clean the inlet filter on your model.
- If descaling is overdue, have it done. The maker advises flushing and descaling every year.
No, there is no hot water at all
Deal with it soon
Call a licensed professional
With power, water and the display all fine, the remaining causes are ignition, gas supply or internal parts, which are not homeowner work.
What to do
- Tell the professional what the display showed and what you checked.
- Do not open the unit or work on gas parts.
- If you smell gas at any time, go back to the top of this tree: leave and call for help.
A water valve was closed and I opened it
Keep an eye on it
Try hot water again, then watch it
Closed water valves are one of the listed reasons for no hot water.
What to do
- Open the hot tap and give the unit a minute to start.
- If there is still no hot water, come back to this tree and answer the code and power questions again.
- Do not touch any gas valve or connection.
Why the questions come in this order
The first question is about gas and carbon monoxide. The CDC lists fuel-burning appliances among the sources of carbon monoxide, and CPSC points to alarms as the backup. A gas smell or an alarm ends the tool with leave and call for help, and it does not ask you to inspect the unit.
The second question covers leaks and burning smells. The manufacturer's own list of reasons to call a professional includes water leaks, so the tool treats a leak as an act-now result.
What an owner can check
Noritz names the causes of no hot water as a gas supply interruption, a power problem, an ignition failure, closed water valves or an error code. This site follows only the parts that are safe. Read the code on the display and write it down. Look it up in the owner's manual and do the reset it describes, once. Check that the unit has power and that its breaker has not tripped. Check that the water valves to the unit are open. The manufacturer also lists the gas valve and gas connections, but the tool leaves those to a licensed professional.
If the symptom is swings between hot and cold, or weak flow, the manufacturer points to mineral scale, a wrong temperature setting, a clogged inlet filter or several fixtures running together. Its maintenance advice is to flush and descale each year. That is a good question to put to a plumber, since scale makes a unit work harder to do the same job.
Setting and energy use
For water heaters in general, the Department of Energy recommends a setting of 120 degrees F, and a lower setting also lowers scalding risk. The Energy Saver Guide puts water heating at roughly 18% of home energy use, so a unit that runs badly is worth fixing promptly.
When to call a professional
Call when an error code returns after the reset, when the unit shuts down repeatedly, when ignition fails, or whenever gas is involved. The tool never describes gas parts, pilot lights or wiring. If a breaker trips a second time, leave it off and call a licensed electrician or plumber.
Worked example
Omar has no hot water in the morning. He smells nothing and no alarm has sounded, and nothing is dripping. The display shows a code, which he writes down. The manual describes a reset, which he does once, and the code comes back after a few minutes. The tool ends with a soon result: call a qualified technician and give them the code. He does not touch the gas connection or open the cabinet. His neighbor has no code at all, finds the breaker tripped, switches it on once and the unit starts. The tool tells her to watch it for a day and to leave the breaker off and call a licensed pro if it trips again.
Renting
Tell the landlord in writing and keep a copy. The renter's repair request letter works for hot water too. A gas smell is a phone call, not a letter.