Skip to content
WattsBack

Furnace blowing cold air

Gas smell, soot, burning or a carbon monoxide alarm means leave and call for help. Otherwise check the thermostat fan setting, the short warm-up delay, the filter and vents, and the fuel, and call a technician for ignition parts.

Photograph of a wall vent with a ribbon fluttering from it beside a frosty window
On this page

There is nothing more confusing than a furnace that is clearly on, with a fan you can hear, and vents that push out cool air. The cause is often a setting or a filter, and sometimes it is a part that must be left to a technician. This page helps you tell which, and tells you what to do first if there is any sign of danger.

Furnace blowing cold air

Gas, carbon monoxide and burning smells first. Then the thermostat fan setting, the short warm-up delay, airflow and fuel, which cover most cold-air calls. Ignition parts and pilots are for a technician.

Do you smell gas, or has a carbon monoxide alarm sounded or anyone felt sick?

I smell gas

Act now

Leave now and call for help

A gas smell can mean a leak, and a furnace that is not lighting is not worth staying in the house for.

What to do

  1. Leave the home now with everyone in it, and keep pets with you if you can do that quickly.
  2. Do not turn lights or appliances on or off, use a lighter or match, or try to find the leak.
  3. From outside, call 911 and your gas utility's emergency number.
  4. Stay out until the utility or the fire department says it is safe.
A CO alarm sounded or someone feels sick

Act now

Get into fresh air and call emergency services now

Fuel-burning equipment that is not burning or venting properly can release carbon monoxide, which has no smell or color.

What to do

  1. Get everyone, including pets, into fresh air now. Open the door on your way out.
  2. Call 911 from outside. Symptoms can look like the flu: headache, dizziness, weakness, nausea or confusion.
  3. Do not go back in to switch the appliance off. Wait for the fire department or a gas utility technician to say it is safe.
  4. Have the appliance inspected by a qualified technician before it runs again.
Neither

Any burning smell, soot around the furnace, smoke, or a breaker that keeps tripping?

Yes, one of those

Act now

Turn it off and call a licensed professional now

Soot, burning smells and a breaker that will not stay reset are warning signs, and the manufacturer says to switch the system off and call a professional for them.

What to do

  1. If you see smoke or flames, or the smell is strong, leave the home and call 911.
  2. Otherwise switch the equipment off at the thermostat and leave any breaker that tripped off. Do not keep resetting it.
  3. Call a licensed HVAC professional or electrician now. Do not open panels or touch wiring.
No

Is the thermostat on heat, with the fan on Auto and the target above the room temperature?

Also check that the schedule is right after a clock change or a power cut.

The fan was on, and I switched it to Auto

Keep an eye on it

Wait through one heating cycle

A fan left on blows room-temperature air whenever the burners are off. This is the most common reason for cold air from a working furnace.

What to do

  1. Leave the fan on Auto and wait for the next heating cycle.
  2. If the air is warm during the cycle and cool after it, that is normal for this setting.
  3. If it is cold during the whole cycle, answer again and keep going down the tree.
The mode, target or schedule was wrong and I fixed it

Keep an eye on it

Give it a few minutes, then watch it

A wrong mode, a target at or below the room temperature or an old schedule stops the furnace from calling for heat.

What to do

  1. Wait several minutes, then feel the vents.
  2. If the air is still cool, come back and answer the next questions.
It is set correctly

Is the air cold only for the first minute or so after the furnace starts?

Yes, it warms up after a short delay

Keep an eye on it

That is normal, so watch it

Most furnaces hold the blower back briefly after the burners light, so the heat exchanger can warm before air moves across it.

What to do

  1. Check the owner's manual for the usual delay on your model.
  2. If the wait is much longer than the manual says, call an HVAC technician.
No, it stays cold or keeps starting over

Is the filter clean, are the supply vents open, and are the return grilles clear of furniture and rugs?

Switch the furnace off before you pull the filter.

No, the filter was dirty or something blocked the air

Keep an eye on it

Restore airflow, then watch it

A dirty filter or blocked air path lets the furnace overheat, so a limit switch shuts the burners off while the blower runs to cool the unit. The air coming out is then cool.

What to do

  1. Replace the filter and clear the vents and returns.
  2. Restore power and watch a full heating cycle.
  3. If the burners keep shutting off, call a licensed HVAC technician.
All fine, but the ducts I can reach feel leaky

Deal with it soon

Ask a contractor about the ducts

Leaky ducts in an attic or crawlspace lose heat on the way to the rooms. Hidden ductwork needs a contractor to find and seal.

What to do

  1. Ask for a duct leakage check and sealing.
  2. In the meantime, make sure every supply vent is open.
All fine

Do your other gas appliances work, and if you use propane or oil, is there fuel in the tank?

My other gas appliances are dead too

Deal with it soon

Call your gas utility

Dead gas appliances throughout the home suggest an interruption in the supply, which no furnace can run without.

What to do

  1. Call your gas utility and ask about service in your area.
  2. Do not touch gas valves or connections.
  3. If you smell gas at any time, leave and call for help from the start of this tree.
The propane or oil tank is empty

Deal with it soon

Call your fuel supplier

A furnace without propane or oil blows cool air because nothing is burning.

What to do

  1. Call your propane or oil supplier for a delivery.
  2. After a delivery, have a technician restart the furnace if it does not recover by itself, because restarting a fuel-burning furnace after it ran dry is a technician's job.
  3. Do not work on fuel lines or relight anything yourself.
Fuel looks fine, or I'm not sure

Deal with it soon

Call a licensed HVAC technician

With settings, airflow and fuel ruled out, the likely causes are a dirty flame sensor, a tripped limit switch, an ignition fault or a failing control board. Each is a technician repair.

What to do

  1. Tell the technician what you checked and whether the furnace takes several tries to start or cycles often.
  2. If your furnace has a standing pilot flame that is out, do not relight it yourself. Ask the technician.
  3. Do not clean the flame sensor, touch burners or work on the control board.

Danger signs first

A furnace that is not heating properly may not be burning or venting properly either. The tool begins with a gas smell, a carbon monoxide alarm or symptoms such as headache, dizziness and nausea. If you answer yes, it ends with an act-now result and the emergency number, 911. Carrier also says that soot around the furnace or a burning smell is a reason to switch the system off and call a professional, so the second question asks for those and for a breaker that keeps tripping.

Why the air is cool

Carrier lists a long set of common causes, and the tool groups them by what you can check safely. Start with the thermostat. A fan left on blows room-temperature air whenever the burners are off, and Carrier calls that the most common reason for cold air from a furnace that works. A wrong mode, a target below the room temperature and an old schedule after a clock change or power cut come next. Then there is the normal wait: many furnaces hold the blower back after the burners light, so the first stretch of air is cool.

If neither of those explains it, airflow is next. A dirty filter or blocked vents let the furnace overheat, and its limit switch then shuts the burners off while the blower keeps running to cool things down. That gives a steady stream of cool air. Duct leaks you can reach with your hand also lose heat in unheated spaces, and DOE's heating guide says leaky ducts can add hundreds of dollars a year to energy costs.

Last is fuel. If your other gas appliances are dead too, call the gas utility. If you use propane or oil, an empty tank is the answer.

What goes to a technician

A dirty flame sensor, a stuck gas valve, a tripped limit switch that comes back, an ignition fault and a failing control board are technician repairs. Carrier's page mentions relighting a standing pilot on older furnaces, but this site does not give relighting steps, and the tool tells you to ask a technician. If the furnace takes several tries to start or cycles often, say so when you call.

Worked example

Kwame comes home to a cold house and a furnace that hums. There is no gas smell, soot or alarm. The thermostat is on heat with the target above the room, but the fan switch reads On. He sets it to Auto, and the next heating cycle brings warm air during the cycle and cool air after it, which the tool calls normal for his setting. A neighbor with the same symptom had a clean fan setting and a clogged filter that had tripped the limit switch; once she swapped it, the burners stayed lit.

Renting

If the furnace is not heating, tell your landlord right away and keep a record of the date. Basic things like setting the fan to Auto are yours; filters, ducts and any burner work belong to the owner. The renter's repair request letter helps you ask.

If the fan itself will not start or stop, use furnace blower not working. The air sealing checklist covers drafts, and the winter bill reduction checklist covers settings that save on the bill.

Sources

  1. Carrier, Why is my furnace blowing cold air? (help page) carrier.com
  2. Carrier, Furnace not turning on (help page) carrier.com
  3. Centers for Disease Control and Prevention, About carbon monoxide cdc.gov
  4. U.S. Consumer Product Safety Commission, Carbon Monoxide Information Center cpsc.gov
  5. U.S. Department of Energy, Consumer Guide to Home Heating and Cooling energy.gov