Lennox gas furnace error codes
Lennox gas furnace code E270: ignition lockout
The furnace used up its tries to light (five trials in all) without the flame sensor seeing a flame, so it is in a soft lockout. Watchguard tries again after one hour, and the code clears after a heating call that finishes normally.

On this page
- Code
- E270
- Equipment
- Lennox gas furnace
- Models
- SL280UHNV and SL280DFNV (SL280V) and EL296DFV two-stage variable speed furnaces
- What to do
- Technician repair
What code E270 means
Lennox's Installation Instructions SL280UHNV (507649-05, 04/2024) lists E270 as ignition lockout, for the SL280UHNV and SL280DFNV (SL280V) and EL296DFV two-stage variable speed furnaces. A single seven-segment LED on the furnace's integrated control board spells out a status letter or an error code one character at a time, so code E250 shows as E, then 2, then 5, then 0.
What usually causes it
The manual points to these causes for this code, roughly in the order a technician would rule them out:
- Not enough gas flow reaching the burners.
- The igniter is not lighting the burner.
- A weak flame sensor signal, so the control cannot prove the flame.
What you can safely check
- Check that gas is reaching the house. If other gas appliances (stove, dryer) also do not work, the problem is the gas supply, so call your gas utility. Do not try to light anything or adjust the gas valve yourself.
- Write the code down before you reset. Many controls forget the code once power is cut. Note it, how often it flashes, and when it happens. A technician can then go straight to the right part.
- Reset it once. Turn the unit off at its switch, wait a minute, and turn it back on, or use the reset the manual describes. One reset clears a passing glitch. If the same code comes back, stop resetting and book a technician.
When to call a technician
Call if the code returns after one reset, if you saw or smelled anything unusual, or as soon as a check above points at a part inside the unit. Tell the technician the brand, the model number from the rating label, and that the control showed code E270 (the manual's first suspect is not enough gas flow reaching the burners). That saves a diagnostic visit from starting at zero.
Step by step for this kind of problem
The Furnace not working troubleshooter walks through the symptom question by question and ends with a clear next step.
Related Lennox codes
Other Lennox gas furnace codes
- A
- C
- d
- h
- H
- dF
- U
- E105
- E110
- E111
- E112
- E113
- E114
- E115
- E116
- E117
- E120
- E124
- E125
- E126
- E131
- E180
- E200
- E201
- E202
- E203
- E204
- E205
- E206
- E207
- E223
- E224
- E225
- E226
- E227
- E228
- E229
- E240
- E241
- E250
- E252
- E271
- E272
- E273
- E274
- E275
- E276
- E290
- E291
- E292
- E294
- E295
- E310
- E311
- E312
- E313
- E331
- E334
- E347
- E348
- E349
- E370
- E400
- E401
- E402
- E403
- E404
- E405
- E406
- E407
- E408
- E409
The full Lennox gas furnace code table lists every code with its meaning, and explains how to read and clear them.
Sources
- Lennox, Installation Instructions SL280UHNV (507649-05, 04/2024) lennox.com
- Lennox, Installation Instructions SL280DFNV Dave Lennox Signature Gas Furnace (508150-02) lennox.com
- Lennox, Unit Information / Service Literature Corp 1126-L5 (revised 08/2022) lennox.com
- Carrier, Furnace not turning on (help page) carrier.com
- U.S. Consumer Product Safety Commission, Carbon Monoxide Information Center cpsc.gov
- Noritz, How to troubleshoot a tankless water heater noritz.com