Lennox gas furnace error codes
Lennox gas furnace code E290: igniter circuit fault
The hot surface igniter, the part that glows red hot to light the gas, or the circuit that powers it has failed. The furnace goes into a one hour soft lockout and clears once a stable flame is proven.

On this page
- Code
- E290
- Equipment
- Lennox gas furnace
- Models
- SL280UHNV and SL280DFNV (SL280V) and EL296DFV two-stage variable speed furnaces
- What to do
- Technician repair
What code E290 means
Lennox's Installation Instructions SL280UHNV (507649-05, 04/2024) lists E290 as igniter circuit fault, for the SL280UHNV and SL280DFNV (SL280V) and EL296DFV two-stage variable speed furnaces. A single seven-segment LED on the furnace's integrated control board spells out a status letter or an error code one character at a time, so code E250 shows as E, then 2, then 5, then 0.
What usually causes it
The manual points to these causes for this code, roughly in the order a technician would rule them out:
- A failed igniter: open, or with a resistance outside its specification.
- A fault in the control circuit that switches the igniter on.
What you can safely check
- Write the code down before you reset. Many controls forget the code once power is cut. Note it, how often it flashes, and when it happens. A technician can then go straight to the right part.
- Reset it once. Turn the unit off at its switch, wait a minute, and turn it back on, or use the reset the manual describes. One reset clears a passing glitch. If the same code comes back, stop resetting and book a technician.
When to call a technician
Call if the code returns after one reset, if you saw or smelled anything unusual, or as soon as a check above points at a part inside the unit. Tell the technician the brand, the model number from the rating label, and that the control showed code E290 (the manual's first suspect is a failed igniter: open, or with a resistance outside its specification). That saves a diagnostic visit from starting at zero.
Step by step for this kind of problem
The Furnace not working troubleshooter walks through the symptom question by question and ends with a clear next step.
Related Lennox codes
Other Lennox gas furnace codes
- A
- C
- d
- h
- H
- dF
- U
- E105
- E110
- E111
- E112
- E113
- E114
- E115
- E116
- E117
- E120
- E124
- E125
- E126
- E131
- E180
- E200
- E201
- E202
- E203
- E204
- E205
- E206
- E207
- E223
- E224
- E225
- E226
- E227
- E228
- E229
- E240
- E241
- E250
- E252
- E270
- E271
- E272
- E273
- E274
- E275
- E276
- E291
- E292
- E294
- E295
- E310
- E311
- E312
- E313
- E331
- E334
- E347
- E348
- E349
- E370
- E400
- E401
- E402
- E403
- E404
- E405
- E406
- E407
- E408
- E409
The full Lennox gas furnace code table lists every code with its meaning, and explains how to read and clear them.
Sources
- Lennox, Installation Instructions SL280UHNV (507649-05, 04/2024) lennox.com
- Lennox, Installation Instructions SL280DFNV Dave Lennox Signature Gas Furnace (508150-02) lennox.com
- Lennox, Unit Information / Service Literature Corp 1126-L5 (revised 08/2022) lennox.com
- Noritz, How to troubleshoot a tankless water heater noritz.com