Skip to content
WattsBack

A.O. Smith gas water heater error codes: what each one means

A.O. Smith's manual for the Residential atmospheric gas water heaters with a status light gas control (75 and 100 gallon) lists 8 codes. A small status light on the gas control, beside the temperature knob, flashes a count and repeats. One flash every three seconds is normal; other counts, a steady light or no light at all point to the pilot, the thermopile or the gas control.

Photograph of a plain white tank water heater with copper pipes in a tidy utility closet
On this page
Codes listed
8
Turn off and call a pro
3
Often an owner fix
3

How to read the code

This heater has a standing pilot and no power cord. A thermopile sits in the pilot flame and makes the small current that runs the gas control, so the status light only starts blinking once the thermopile is warm. After lighting, it can take up to 90 seconds of steady pilot flame before the first blink, even though the pilot is already lit.

To light it, the label has you hold the knob in at PILOT and press the igniter button about once a second until the light starts to blink. A.O. Smith limits this to three tries, with a ten minute wait between each one, because the control's circuitry needs that pause. If the light still does not blink after the third try, turn the knob to OFF and call a technician or your gas supplier.

A steady light means the gas control is shutting down: the pilot has gone out and the thermopile is cooling. Wait the full ten minutes before trying again. Four flashes is easy to miss, because the overheat shutoff also puts the pilot out, so the code only shows right after a relight. That shutoff is built into the gas control and cannot be reset; the control has to be replaced.

The manual is firm about flammable vapors. If the heater was running, then stopped and will not relight, a technician should check for signs that vapors caught fire inside it. A heater that has been through a vapor ignition must not be used and has to be replaced as a whole, not repaired.

A.O. Smith gas water heater code table

Codes with a link have their own page with causes and the checks that fit that code.

A.O. Smith gas water heater codes, from the Instruction Manual - Residential Gas Water Heaters, incl. status light codes (100276479)
CodeWhat it meansWhat to do
0 flashesPilot out, no status light. The status light is dark because the pilot is not lit or the thermopile, the part the pilot flame heats to power the control, is not yet warm. With no pilot the burner cannot fire, so the tank goes cold.Often an owner fix
Light on (solid)Pilot just went out. A steady light means the pilot went out a short time ago and the thermopile is still cooling, so the control is shutting down.Often an owner fix
1 flashNormal operation. One flash every three seconds means the pilot is lit and the control is working. Nothing needs fixing.Often an owner fix
2 flashesThermopile output too low. The pilot is burning, but the thermopile is not making enough voltage to run the gas control, so the burner will not come on.Technician repair
4 flashesWater overheated, gas shut off. The gas control's temperature sensor found the water too hot and shut off both the main burner and the pilot. This shutoff cannot be reset, and the gas control has to be replaced.Turn it off and call a pro
5 flashesTank temperature sensor failed. The thermistor that reads the tank temperature for the gas control is faulty, and the fix is a new gas control.Technician repair
7 flashesGas control failure. The gas control valve itself has failed. The manual has the gas turned off and the control replaced.Turn it off and call a pro
8 flashesPower still present after shutoff. The knob was turned to OFF, yet the thermopile kept making power. Either it is cooling slower than expected or the pilot is still burning because its valve stuck open, which means gas is flowing when it should not be.Turn it off and call a pro

Codes that mean turn it off

These codes come from a flame, gas, venting or overheat safety. Leave the unit off and call a licensed technician rather than resetting it repeatedly:

Code by code

No code showing?

If the unit is not working and shows no code at all, start with the Water heater, no hot water troubleshooter. It covers power, settings and supply problems that stop the control from running at all.

More error code tables

Sources

  1. A.O. Smith, Instruction Manual - Residential Gas Water Heaters, incl. status light codes (100276479) assets.aosmith.com
  2. Carrier, Furnace not turning on (help page) carrier.com
  3. U.S. Consumer Product Safety Commission, Carbon Monoxide Information Center cpsc.gov
  4. Noritz, How to troubleshoot a tankless water heater noritz.com