Skip to content
WattsBack

Rinnai tankless water heater error codes

Rinnai tankless water heater code 10: air supply or exhaust blocked

The heater cannot move enough combustion air in or exhaust out, or on condensing SENSEI models the condensate trap has filled up. It shuts down rather than run with blocked venting.

Photograph of a plain white wall-mounted tankless water heater with insulated pipes below it
On this page
Code
10
Equipment
Rinnai tankless water heater
Models
SENSEI and non-SENSEI tankless: RU, RUR, RUC, RE, RX, CX, RL, V series (incl. V53De), RH180
What to do
Turn it off and call a pro

What code 10 means

Rinnai's Troubleshooting Tankless Water Heater Diagnostic Codes (100000652) lists 10 as air supply or exhaust blocked, for the SENSEI and non-SENSEI tankless: RU, RUR, RUC, RE, RX, CX, RL, V series (incl. V53De), RH180. The code flashes as two digits or two letters on the temperature controller or the heater's front display, for example 11, 12 or LC. It stops flashing once the problem is fixed and the heater is supplying hot water again.

What usually causes it

The manual points to these causes for this code, roughly in the order a technician would rule them out:

  • The condensate drain line is clogged or frozen, so water backs up into the trap inside the heater (SENSEI models).
  • The inlet air filter under the front cover is dirty.
  • The intake or exhaust pipe is blocked, damaged, collapsed, too long or not made of approved material.
  • Insects, debris or water are inside the vent pipe.
  • The vent terminal is too close to another terminal, a wall, an overhang or the ground.
  • The fan, its check valve, its wiring or the PC board has a problem, or the altitude setting is wrong.

What you can safely check

  1. Look at the vent pipes outside. High-efficiency furnaces, boilers and tankless heaters breathe through plastic pipes on an outside wall or the roof. From the ground, check that snow, ice, leaves or a nest are not blocking either opening, and clear what you can reach safely.
  2. Look at the condensate drain. Condensing equipment makes water that drains through a small hose or trap. A kinked hose, a full pump or water pooling under the unit can make it shut down. Straighten a kinked hose and empty a full pump reservoir; leave the trap itself to a technician.
  3. Write the code down before you reset. Many controls forget the code once power is cut. Note it, how often it flashes, and when it happens. A technician can then go straight to the right part.

When to call a technician

Call if the code returns after one reset, if you saw or smelled anything unusual, or as soon as a check above points at a part inside the unit. Tell the technician the brand, the model number from the rating label, and that the control showed code 10 (the manual's first suspect is the condensate drain line is clogged or frozen, so water backs up into the trap inside the heater (SENSEI models)). That saves a diagnostic visit from starting at zero.

Step by step for this kind of problem

The Tankless water heater, no hot water troubleshooter walks through the symptom question by question and ends with a clear next step.

Other Rinnai tankless water heater codes

The full Rinnai tankless water heater code table lists every code with its meaning, and explains how to read and clear them.

Sources

  1. Rinnai, Troubleshooting Tankless Water Heater Diagnostic Codes (100000652) media.rinnai.us
  2. Rinnai, V53De Installation and Operation Manual, incl. diagnostic codes (100000561) media.rinnai.us
  3. ENERGY STAR, Maintenance Checklist (heating and cooling) energystar.gov
  4. Noritz, How to troubleshoot a tankless water heater noritz.com